User manual TYAN TOMCAT K8SH

[. . . ] Tomcat K8SH /// Revision 1. 10 S3850 Copyright © TYAN Computer Corporation, 2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, AMD Opteron, and combinations thereof, are trademarks of Advanced Micro Devices, Inc. HyperTransport is a licensed trademark of the HyperTransport Technology Consortium. [. . . ] BIOS Setup Utility Main Advanced PCI/PnP Boot Security AMD PowerNow Configuration Chipset Exit Enabled/Disabled PowerNow. Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit PowerNow [Disabled] 46 http://www. tyan. com Feature Option AMD PowerNow Configuration Enabled PowerNow Disabled Description Enabled/Disabled PowerNow 3. 5. 12 ­ Remote Access Configuration Sub-Menu You can use this screen to view the Remote Access Configuration Menu. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Select remote access type. Select Screen Select Item +/- Change Field F1 General Help F10 Save and Exit ESC Exit Configure Remote Access type and parameters Remote Access Serial port number Base Address, IRQ Serial port Mode Flow Control Redirection After BIOS POST Terminal Type VT-UTF8 Combo Key Support Sredir Memory Display Delay [Disabled] [COM1] [3F8h, 4] [115200 8, n, 1] [None] [Always] [ANSI] [Disabled] [No Delay] Feature Option Description Configure Remote Access type and parameters Enables remote access to system Enabled Remote Access through serial port. Disabled Serial port number Base Address, IRQ COM1 COM2 Read only 115200 8, n, 1 57600 8, n, 1 38400, 8, n, 1 19200 8, n, 1 09600 8, n, 1 47 Selects Serial Port for console redirection. Selects Serial Port settings. Serial port Mode http://www. tyan. com Feature Option Description Configure Remote Access type and parameters None Selects Flow Control for console redirection. Flow Control Hardware Software Disabled Redirection After BIOS POST Disable: Turns off the redirection after POST Boot Loader: Redirection is active during POST and during Boot Loader. <Some OSs may not work if set to Always> Selects the target terminal type. Boot Loader Always ANSI VT100 VT-UTF8 Disabled Enabled No Delay Delay 1 sec Delay 2 sec Delay 4 sec Terminal Type VT-UTF8 Combo Key Support Sredir Memory Display Delay Enables VT-UTF8 Combination key Support for ANSI/VT100 terminals. This file allows user to select the delay in seconds to display memory information. 3. 5. 13 ­ USB Configuration Sub-Menu You can use this screen to view the USB Configuration Menu. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit USB Configuration Module Version ­ X. XX. X-XX. X USB Devices Enabled: None Legacy USB Support BIOS EHCI Hand-Off [Enabled] [Enabled] Enables USB host controllers. Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit 48 http://www. tyan. com Feature USB Configuration Option Description Enables support for legacy USB. Disabled Legacy USB Support Enabled Enabled BIOS EHCI Hand-Off Disabled This is a work around for OSes without EHCI hand-off support. The EHCI ownership change should claim by EHCI driver. 3. 5. 14 Device & PCI Slots Configuration Sub-Menu You can use this screen to enable the onboard devices and PCI slots. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Onboard Device and PCI Slots Configuration Onboard LAN1 Device Onboard LAN1 OP-ROM Onboard LAN2 Device Onboard LAN2 OP-ROM [Enabled] [Disabled] [Enabled] [Disabled] Enabled Disabled Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Description Feature MPS Configuration Onboard LAN1 Device Onboard LAN2 Device Option Disabled Enabled/Disabled LAN controller Enabled Disabled Executed LAN OPROM or not Enabled Onboard LAN1 OP-ROM Onboard LAN2 OP-ROM 49 http://www. tyan. com 3. 6 ­BIOS PCI/PnP Menu You can use this screen to view PnP (Plug & Play) BIOS Configuration Menu. This menu allows the user to configure how the BIOS assigns resources & resolves conflicts. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. BIOS Setup Utility Main Advanced PCI/PnP Boot Security Advanced PCI/PnP Settings WARING: Setting wrong values in below sections may cause system to malfunction. Clear NVRAM Plug & Play O/S [No] PCI Latency Timer [Yes] Allocate IRQ to PCI VGA [64] Palette Snooping [Yes] PCI IDE BusMaster [Disabled] [Disabled] Chipset Exit Clear NVRAM during System Boot. Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit 50 http://www. tyan. com Feature Advanced PCI/PnP Settings Clear NVRAM Option No Yes Yes Description Clears NVRAM during system Boot. Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. [. . . ] VGA (Video Graphics Array): the PC video display standard V-SYNC: controls the vertical scanning properties of the monitor. 68 http://www. tyan. com ZCR (Zero Channel RAID): PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. 69 http://www. tyan. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. [. . . ]