User manual TYAN TRINITY KT400

[. . . ] Trinity KT400 S2495 User' Manual s Trinity KT400 /// Revision 1. 02 S2495 Copyright © TYAN Computer Corporation, 2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Trinity, KT400 and S2495 are trademarks of TYAN Computer Corporation. [. . . ] Enabled / Disabled UR2 Duplex Mode: This item allows you to select IR "Half" or "Full" duplex function. Half / Full 3-17 http://www. tyan. com Trinity KT400 S2495 Chapter 3: BIOS Setup Use IR Pins: This item allows you to select IR transmission routes, one is "RxD2, TxD2 (COM Port) and the other is IR-Rx2Tx2. RxD2, TxD2 / IR-Rx2Tx2 Onboard Parallel Port: This field allows the user to configure the LPT port. 378/IRQ7 / 278/IRQ5 / 3BC/IRQ7 / Disabled Parallel Port Mode: This field allows the user to select the parallel port mode. SPP / EPP / ECP / ECP+EPP EPP Mode Select: This item allows you to determine the IR transfer mode of onboard I/O chip. EPP1. 9 / EPP1. 7 ECP Mode Use DMA: This field allows the user to select the DMA1 or DMA3 for the ECP mode. 201 / 209 / Disabled Midi Port Address: Select an address for the MiDi port. 290 / 300 / 330 / Disabled Midi Port IRQ: Select an interrupt for the MiDi port. 5 / 10 3-18 http://www. tyan. com Trinity KT400 S2495 Chapter 3: BIOS Setup 3. 6 ­ Power Management Setup Options related to power management can be altered through the following: Phoenix ­ AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function ACPI Suspend Type Power Management Option HDD Power Down Suspend Mode Video Off Option Video Off Method MODEN Use IRQ Soft-off by PWRBTN Run VGABIOS if S3 Resume States After Power Failure ?IRQ/Event Activity Detect [Enabled] [S1 (POS)] [User Define] [Disabled] [Disabled] [Suspend -> off] [V/H SYNC+Blank] [3] [Instant] [Auto] [Auto] [Press Enter] Item Help _________________________ Menu Level ? : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults ACPI Function: Toggles advanced power and configuration done by OS. Enabled / Disabled ACPI Suspend Type: Defines ACPI system suspend mode. S1 (POS) Power Management Option: Defines the type of power saving features the system should follow. User Define / Maximum Saving / Minimum Saving HDD Power Down: Defines hard drive power down delay. Disabled / 1 minutes / 5 minutes / 10 minutes / 30 minutes / 45 minutes / 60 minutes Suspend Mode: Defines the method used to power off the system. Disabled / Standby / Sleep Video Off Option: Tell you what time frame that the video will be disabled under current power management settings. Always On / Suspend -> Off 3-19 http://www. tyan. com Trinity KT400 S2495 Video Off Method: Defines the method used to power off graphics. V/H SYNC+Blank / Blank / DPMS Chapter 3: BIOS Setup MODEM Use IRQ: Name the interrupt request (IRQ) line assigned to the modem (if any) on your system. N/A / 3 / 4 / 5 / 7 / 9 / 10 / 11 Soft-off by PWRBTN: Defines the action of the power button when pressed. Instant-Off / 4-seconds States After Power Failure: This field lets you determine the state that your PC returns to after a power failure. If set to "Off", the PC will not boot after a power failure, if set to "On", the PC will restart after a power failure. Auto / On / Off IRQ/Event Activity Detect: Phoenix ­ AwardBIOS CMOS Setup Utility IRQ/Event Activity Detect PS2KB Wakeup Select PS2KB Wakeup from S3/S4/S5 PS2MS Wakeup from S3/S4/S5 USB Resume from S3 VGA LPT & COM HDD & FDD PCI Master PowerOn by PCI Card Wake Up On LAN / Ring RTC Alarm Resume X Date (of Month) X Resume Time (hh: mm: ss) ?IRQs Activity Monitoring [Hot Key] [Disabled] [Disabled] [Disabled] [OFF] [LPT / COM] [ON] [OFF] [Disabled] [Disabled] [Disabled] 0 0: 0: 0 [Press Enter] Item Help _________________________ Menu Level ? [. . . ] Reserved Reserved Description Appendix II: Post Error Code for BIOS Switch back to text mode if full screen logo is supported. -If errors occur, report errors & wait for keys -If no errors occur or F1 key is pressed to continue: wClear EPA or customization logo. Reserved Reserved Description 80h: 81h: E8POST. ASM star ts 82h: 1. Save all data in stack back to CMOS Initialize ISA PnP boot devices 1. [. . . ]