Detailed instructions for use are in the User's Guide.
[. . . ] 7 OSD MENUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DIRECT CONTROL KEYPAD BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DISPLAY MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 AUTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Never place heavy or sharp objects on the LCD display, video cable, or power cord. Overloading Outlets Do not overload electrical power sources when installing LCD Monitor. Overloading wall outlets, circuits, or extension cords can result in overheating, fire, or electronic shock. Power supply cords should be routed away from foot traffic and contact with other objects. Periodically inspect power cords for wear or damage, particularly near plug and the point where it exits from the product. Ventilation Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Keep LCD Monitor a minimum of four (4) inches away from any wall to assure sufficient airflow and ventilation. Increased temperatures may cause fire or device failure.
2
To assure proper ventilation, do not block the openings by placing the product on a bed, sofa, rug or other similar surface. Do not place the product in a built-in installation, such as a bookcase or enclosed rack, unless proper ventilation is provided. Your warranty does not cover repairs or attempted repairs by anyone not authorized by manufacturer. If smoke, abnormal noise, or strange odor is present, immediately unplug the power cord. Contact a qualified service technician If your LCD Monitor will not be used for extended periods of time, unplug the power cord.
3
Cleaning the LCD Display
· · MAKE SURE THE LCD DISPLAY IS TURNED OFF NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR CASE 1. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the screen:
To clean the case:
1. If still not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
Manufacturer does not recommend the use of any ammonia or alcohol-based cleaners on the LCD display screen or case. Some chemical cleaners have been reported to damage the screen and/or LCD display case. Manufacturer will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
4
Safety Guidelines
Warning: This device must be operated with the original power supply, part number: ADP-60CF A. CAUTION: The socket-outlet should be installed near the equipment and should be easily accessible. Always use the appropriate AC cord that is certified for the individual country. Some examples are listed below: USA. . . . . . . . . . . . . . . . . UL Switzerland . . . . . [. . . ] These modes automatically change the backlighting levels between bright, brighter and brightest.
Auto
Pressing the AUTO button on the control keys will adjust automatically the picture and synch the LCD Monitor.
The LCD monitor will start the Auto Adjust process automatically and run for approximately 10 seconds, during which time you will notice the image changing and re-synching.
9
Image not Displayed
Input Source Not Found
If there is no source connected to the Input selected.
Out of Range
If the Display settings is not compatible or out of range of the LCD Monitor the following will be displayed:
10
Appendix
Specifications
Panel Optimum Resolution Response Time Contrast Ratio Maximum Brightness Viewing Angles Color Saturation Wall/Arm Mount Input Signal Physical Video Audio Speaker Output Power Operating Conditions Voltage Temperature Humidity Altitude Storage Conditions Temperature Humidity Altitude Dimensions Physical Type 17" Color TFT LCD 1280 x 1024 14 ms 350:1 350 Nits 160° (H) / 140° (V) 72% TBD 75mm VESA® HD-15 pin mini D-Sub (VGA connector) 3. 5mm Mini-Stereo jack male-male Built-in audio amplifier and speakers, 2. 5 watts * 2 channels 100-240 VAC, 50/60 Hz (auto switch), 1. 5A 32° F to +95° F (0° C to +35° C) 20% to 90% (no condensation) To 3, 000 Meter -4° F to + 140° F (-20° C to + 60° C) 10% to 90% (no condensation) To 12, 000 Meter 15. 1 (w) x 16. 2 (h) x 8. 3 (d) in 17. 5 (w) x 18. 2 (h) x 5. 1 (d) in Weight Regulations Power consumption DC on DC Off Lamp Life Net 7. 7 lb (2. 8 kg) FCC-B, UL, CSA (CUL), Energy Star®, Plug & Play <73W <3W (Blue LED) (LED OFF)
40, 000 hours
11
Troubleshooting
No power
· · · Make sure DC cord is plugged into the back of the LCD Monitor. Make sure AC power cord is securely connected to the AC socket Plug another electrical device (like a radio) to the power outlet to verify that the outlet is supplying the proper voltage
No Image
· · Make sure power button is ON. Check whether the LCD monitor and computer power cords are plugged in and whether there is a supply of power.
Power is ON but no screen image
· · · Adjust brightness and contrast Check signal connection properly seated both on PC and Monitor.
"Out Of Range"
Check the computer image output resolution and frequency and compare the value with the preset values of graphics card.
Fuzzy Image
· · · · · Adjust Phase.
Image to Bright or to Dark
Adjust brightness and contrast by OSD. Irregular Image Check the signal connection between the computer and LCD monitor. [. . . ]