User manual WESTINGHOUSE W32001

[. . . ] 20. 1" LCD Display Preface About this Manual This manual is designed to assist you in setting up and using your LCD display. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. Copyright © Copyright 2003. [. . . ] Contact your dealer or a qualified service technician if the plug does not fit into the outlet. 3 Insert the small end of the adapter cord into the DC-in connector at the back of the LCD display. The power LED on the front panel glows orange. 2. 11 Turning On the LCD Display 1 Press the Power key on the LCD display control panel or remote control to turn the LCD display on. The power LED on the front panel glows green. 2 Press either Power key again to turn the LCD display off. 10 Adjusting Settings 3 Adjusting Settings ENGLISH This chapter explains the LCD display's On-Screen Display (OSD) menus. These are used to adjust settings related to picture and audio quality, as well as other features. Using the OSD you can adjust the contrast, brightness, OSD position, color temperature, stereo speaker volume, and other settings. The OSD Menus can be accessed using either the remote control or the display control panel located on the top of the LCD display. 3. 1 Controlling the OSD Press the MENU button to turn the OSD on or off. LCD Control Panel MENU CH VOL CH Remote Control Description MENU · turns on the OSD menu · confirms a selection i MENU MENU CH VOL CH i MENU OFF/BACK · turns off the OSD menu · exits a menu without making any changes / arrow keys navigates through the OSD menus · adjusts value · arrow keys navigates through the second level of the OSD menus VOL CH VOL CH i MENU PRG / CH VOL CH · MENU i 11 Adjusting Settings 3. 2 Setting the Main Display Mode You can switch between input sources and display them on the main screen in sequence by repeatedly pressing either: · · the SOURCE key on the remote control the SOURCE key on the LCD control panel The Main display mode rotates between: · · · · · TV AV S-Video YPbPr VGA 1 : TV 2 : OFF VGA YPbPr Main display mode indicator The OSD menus for each display mode allow you to set options that are specific to the selected video signal format. Refer to "Adjusting Settings" on page 11 for information on adjusting settings for each display mode. 3. 3 Setting the Picture-in-Picture Display Mode The LCD display is capable of displaying a second video input signal on the LCD screen at the same time as the main signal. This second signal, or source, is shown on the LCD screen in a box over top of the main image this is referred to as "Picture-in-Picture" (PIP). 1 : TV 2 : OFF VGA YPbPr PIP display mode indicator 12 Adjusting Settings PIP Select the PIP source by pressing the PIP key on the remote control. Sub signal options vary according to the selected Main signal as shown in the following table. PIP (Picture-in-Picture) Main TV AV S-Video YPbPr VGA OFF TV AV S-Video YPbPr VGA - - - - - - - - - - - - - 13 ENGLISH Main Adjusting Settings 3. 4 Adjusting the Display The following table indicates the display settings that are available for each Main display mode. Setting Contrast Brightness Color Hue Sharpness Focus Auto Color Red Green Blue White Balance TV - - - - - - - AV - - - - - - - S-Video - - - - - - - YPbPr - - - - - - VGA - - - - NOTE: To return all DISPLAY settings to their factory defaults, select "Recall" from the menu and press the key. Contrast: enables you to adjust the difference between the lightest and darkest areas of the LCD display screen. Contrast should be adjusted in conjunction with the brightness item. Brightness: enables you to adjust the light level of the LCD display's screen. Select "User" to set a custom color temperature. Hue: allows you to adjust the display hue. Hue is a measure of the saturation of a color. Sharpness: enables you to adjust the sharpness of the image. Recall: returns all display settings to their factory-set default values. 14 Adjusting Settings 3. 5 Television Settings 3. 5. 1 Setting Channels When connected to a television antenna or CATV cable, the LCD display can automatically scan for available channels. Before scanning, make sure you have selected the correct TV signal source: air (broadcast) or CATV (cable TV). To scan for channels: R GB TV CH-Scan C. CPT V-Chip TV-SYSTEM OFF AIR 1 Press MENU to turn the OSD on. R GB 2 Press VOL+ to switch to the TV menu. TV CH-Scan C. CPT V-Chip TV-SYSTEM 125 OFF CATV 3 Press PRG/CH CH-Scan. to select 4 Press VOL + to begin scanning channels. 5 The screen displays a number incrementing from 1 to 125 (for NTSC systems in the USA and other countries) as the LCD display scans for available channels. 6 Scanning is complete when the channel number stops incrementing (125 for NTSC systems). The channel switches back to the first available channel found. NOTE: Several minutes are required for channel scanning to complete. 15 ENGLISH Adjusting Settings 3. 5. 2 Using Quick Channels The quick channel function lets you assign ten channels that can be accessed by the quick channel keys on the remote control. [. . . ] Setting Clock Phase H-Position (Horizontal Position) V-Position (Vertical Position) Description Adjusts pixel alignment to help stabilize the VGA display. Centers the image on the display vertically. R GB OSD GEOMETRIC Clock Phase H-Position V-Position 123 29 21 33 Recall 3. 7 Adjusting Volume Use VOL+/­ to increase or decrease the volume. 18 Press MUTE to turn the sound off completely. Any change in volume, channel, VGA timing, or input source will release the mute function. 18 20 Adjusting Settings NOTE: ENGLISH To return all audio settings to their factory defaults, select "Recall" from the menu and press VOL+. 3. 8 Miscellaneous Settings 3. 8. 1 Setting the OSD Timer You can change the length of time the OSD will remain on the screen after the last key has been pressed. Available options are: 5, 10, 15, 20, 25 or 30 seconds. 3. 8. 2 Setting the OSD Language You can change the language in which the OSD menus appear. [. . . ]