User manual X10 IR18A

[. . . ] IconRemote (Single User) TM Owner's Manual Model IR18A Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Introduction Congratulations on your purchase of this Universal Remote Control. [. . . ] Repeatedly press SELECT to select the desired mode (TV, VCR, etc. ), unless the desired mode is already selected. To find the first digit for the code stored under the mode selected in Step 2, press each number button (0-9). When the indicator blinks off, the number you pressed is the first code digit you are searching for. 8 9 Setting Favorites The Favorites feature is what really sets this remote apart from other remotes. It lets you go to your favorite channel(s) by simply pressing a button next to a sticker (or label) that represents that favorite channel. Press and hold SETUP until the indicator remains on, then release SETUP. Repeatedly press SELECT to select the desired mode (TV, VCR, etc. ), unless the desired device is already selected. Note: You can use up to 5 buttons, including 0 through 9, OK, and - to enter your favorite channel: 550, 472Enter, 162OK, 5-7, etc. , are examples. Attach the sticker that represents the favorite channel you set up above to the location next to that FAVORITE button. 11, we've used a CNN sticker for the top right-hand FAVORITE button. ) Follow Steps 1 through 6 to set up more favorites, each time selecting a different FAVORITE button in Step 3, and entering a different channel number in Step 4. Then place the appropriate sticker next to the FAVORITE button, as in Step 6. For example, if you have 2 DVD, VCR, or DVR devices programmed into this remote, the last device you used controls the 6 VCR buttons. Note: This feature will not operate if the programmed TV, SAT or Cable code has its own VCR transport button control e. g. a TV Combo, SAT/PVR, etc. Setting Any Mode to Use its Own Volume/ Mute Control You can set any mode to use only its own Volume/Mute control. Note: If your chosen mode does not have Volume/Mute functions, then this remote's VOLUME and MUTE will not operate. Press and hold SETUP until the indicator remains on, then release SETUP. Press and hold MUTE until the indicator blinks off, then release the button. Press and release SELECT to select the desired mode (TV, VCR, etc. ); the indicator blinks, then stays on. Press and release VOLUME- (down); the indicator blinks, then stays on. All modes will now "punch-through" to the respective modes you have chosen for Volume/ Mute control. Volume/Mute Control and Punch-Through Feature Your remote allows you to select which device mode controls VOLUME and MUTE. This remote is initially set for all device modes to use their own Volume/Mute control if present. If the programmed code does not have Volume/Mute operation, then VOLUME and MUTE will "punchthrough" (hand-over) control to the TV-mode device without you needing to change to TV mode. [. . . ] Press and hold SETUP until the indicator remains on, then release SETUP. Repeatedly press and release SELECT to select the desired mode (TV, VCR, etc. ). Press and release the button that you want to learn (for instance, POWER). Point your original remote at the bottom of your new remote until they are about 1 inch apart. [. . . ]