User manual X10 VK74A

[. . . ] OWNER'S MANUAL XM14A POWER SUPPLY C1 CAM ERA C2 C3 C4 P1 POSITION P2 P3 Cente r P4 Sweep CAMERA (SOLD SEPARATELY) M . O . K . A . C . . E . I. G SCAN Normal Pro gra m CR14A REMOTE ZC15A PAN 'N TILT BASE MODEL VK74A PAN 'N TILT CAMERA SYSTEM INCLUDES ZC15A PAN 'N TILT BASE, XM14A ADDRESSABLE POWER SUPPLY, CR14A REMOTE (CAMERA SOLD SEPARATELY) INTRODUCTION The VK74A includes the ZC15A Pan `n Tilt Camera Base with XM14A remote controlled power supply, and the CR14A remote control. You attach any XCam2 wireless camera (XX11A or XX13A) or any XCam 2 Instant On Camera (XX16A or XX17A) to the Pan `n Tilt Camera Base and then you can remotely control the camera's position using a CR14A remote control. The camera sends the picture and sound to a Receiver that you connect to your TV, up to 100 ft. [. . . ] Set each power supply to a different number within one of the groups (1-4, 5-8, 9-12, or 13-16). 5. Position the Video Receiver in a convenient location such as on top of the TV and orient the antenna so that the flat side points in the direction of the room where you set up the Camera. Point antenna towards the Receiver IF YOUR TV IS ALREADY HOOKED UP TO A DBS RECEIVER OR OTHER A/V DEVICE, OR IF YOUR TV DOES NOT HAVE A VIDEO IN JACK Outdoors Indoors If a DBS Receiver or other A/V component is connected to the TV using A/V cables, you can connect the Video Receiver to the free LINE IN jacks on the component. 10 11 REMOTE CONTROL The Remote lets you move the camera from left to right (Pan) and up and down (Tilt). You can store 4 positions for the camera and use the remote to "Sweep" between these positions. Install 4 AAA alkaline batteries (sold separately) in the remote's battery compartment. "Tilts" up and down. Pressing any of these turns on that camera, and turns the other 3 off (Transceiver required). Sweeps thru the 4 stored positions for the selected camera. Pro m gra SINGLE CAMERA OPERATION Press a left or right BLUE button at the top of the CR14A Remote to "Pan" the camera left or right. Press a BLUE up or down button to "Tilt" the camera up or down. Buttons P1 thru P4 are used to store 4 position settings for the camera. To store the first position for the camera, press the BLUE buttons to scan to the position you want. To store the second position for the camera, press the BLUE buttons to scan to the position you want. To store the third position for the camera, press the BLUE buttons to scan to the position you want. To store the fourth position for the camera, press the BLUE buttons to scan to the position you want. To clear all stored positions: Move the switch at the bottom to Program. Press C2 and repeat steps 2 to 7 above to store 4 positions for Camera C2. To control up to 4 Cameras, plug each one into its own Addressable Power Supply, and set each power supply to the same Housecode you set on the Transceiver and the Remote. Pressing any Camera button (C1, C2, C3, or C4) turns on that camera (1, 2, 3, or 4) and turns the others (in the group) off. Then, each press of either the or button turns on the next or previous camera in the group of 4 while turning the current camera off. You must set all cameras to the same channel as the Video Receiver VR31A, or VR36A (Channel A, B, C, D). To "Pan" or "Tilt" a camera: Press C1, C2, C3, or C4 to turn on the camera. Then press a left or right BLUE button at the top to "Pan" the camera left or right. Press a BLUE up or down button to "Tilt" the camera up or down. Press C3 and repeat steps 2 to 7 above to store 4 positions for Camera C3. [. . . ] If the camera gradually drifts off the positions you have programmed: This can happen if the positions you programmed do not cause the camera to pass through center. If you notice the positions that you programmed for sweep starting to drift out of position after a while, just press the Center button on the remote to reset the positions to where you programmed them. Or you can make the camera periodically center automatically as follows: Within 3 seconds after you plug the camera's power supply in, press P1, P2, P3, or P4 on the remote. Pressing P1 within 3 seconds after you power up forces the camera to recenter every 32 sweeps through the positions you have programmed. Pressing P2 within 3 seconds after you power up forces the camera to recenter every 64 sweeps through the positions you have programmed. [. . . ]