User manual X10 WIDEEYE QUICK SETUP

[. . . ] Plug its power supply into a standard wall outlet and the other end into the video receiver. Connect the video receiver to your TV. OWNER'S MANUAL PLEASE KEEP FOR FUTURE REFERENCE For help or more information on setup, please visit: http://www. x10. com/support X10. com, a division of X10 Wireless Technology, Inc. XCam2-12/02 Plug the camera's power supply into a standard wall outlet. Connect the video cable into the video-out jack on the video receiver and into the video-in jack on your TV. 3 4 Basic Camera Setup, cont. Turn on the video receiver. Basic Camera Setup, cont. Fine tune the antennas. Options, cont. Recording with a VCR You can configure your XCam2 camera so that you can record its video signal on your VCR. [. . . ] When you do that, the current camera switches off and camera 2 switches on, displaying its picture. Note: If you have 8 cameras set up, before turning on a camera in group 1-4, turn off any cameras in group 5-8, and vice versa. Multi-Camera Systems, cont. Using Different Unit Codes If you need to set your cameras to unit codes other than 1 through 4, make sure that you use Unit Codes within one of the three other camera groups: 5-8, 9-12, and 13-16. When you change the Unit Codes on your cameras, you will also need to change the Unit Code grouping on your remote control. To set Put the Then press to group: switch to: and hold: 1-4 5-8 9-12 13-16 1-8 1-8 9-16 9-16 1 On 5 On 9 On 13 On And then: Accessories Ninja Pan `n Tilt Increase the viewable area of your camera by 400%. The standard XCam2 records everything within a 60° x 60° field of view. But with the Ninja Robotic Mount, you get sweeping 240° x 130° views. VCR Commander Record only when there's movement in your camera's field of view. The VCR Commander issues "STOP" and "START" commands to your VCR anytime there's movement within 30 feet of your camera. With XRay Vision Software you can monitor your home from any computer with an Internet connection. E-mail video snapshots to your personal account or view them on your own secure Web Site. 6. A picture will appear on your TV. Scanning Between Cameras with the Remote If you select a camera with the remote, you can then use the scan buttons to cycle through cameras 1 through 4. Then use the blue arrow buttons at the bottom of the remote to go to the next or previous cameras. Each press of the button switches to the next or previous camera in order. Press 1 On to switch to camera 1 and then 2 On to switch back to camera 2. Flip the switch back and forth once, and release the button. Repeat steps 6 through 8 for each additional camera, changing the Unit Code as appropriate. For each extra camera, set the Unit Code (number) dial to the next number. For example, your third camera will be set to `3, ' your fourth camera set to `4' and so on. Set all 9 cameras to A. Flip the label on the remote over if you are using cameras 9 thru 12 or 13 thru 16. Set House Code the same as cameras. 10 Troubleshooting, cont. 11 Visit x10. com for more details. 12 Troubleshooting If there's no camera picture on your TV: 1. Make sure your Wireless Video Receiver is connected to power and turned on. Troubleshooting, cont. If the picture on your TV isn't clear: First, adjust the antennas on the video receiver and camera so they point towards each other. The side of the camera's antenna with the dot on it should face the side of the receiver's antenna marked with four squares. You can also try moving the video receiver itself to another location near the TV. If the camera picture still doesn't improve after adjusting the antennas and receiver position, try changing the channels on the camera and video receiver. The channel switch is on the top of the camera (under the rubber plug) and the bottom of the wireless video receiver. [. . . ] See your TV's owner's manual if you still aren't sure how to change the video source. Follow the setup steps again (steps 1 thru 7 ), and check that you have done each step correctly. Make sure that the ABCD switches on the top of the camera and the bottom of the wireless video receiver are set to the same letter. On the camera, the bottom switch position is A and the top position is D. [. . . ]