User manual ZIBRO PX 643

[. . . ] PX 643 2 6 5 3 4 > 1 : BEDIENUNGSANLEITUNG BRUGSANVISNING INSTRUCCIONES DE USO MANUEL D'UTILISATION OPERATING MANUAL ISTRUZIONI D'USO GEBRUIKSAANWIJZING INSTRUKCJA OBSLUGI 4 20 36 52 68 84 100 116 IMPORTANT COMPONENTS Control Panel Air outlet Carrying handle Caster wheels Water container Air filter Air inlet Exhaust air outlet Cord storage Water stopper / drainage point Connection tube Cabinet cover for quick connector shielding Bracket Spanners Remote control Screws (8x) Protection caps for connector (2x) 1. IN CASE OF ANY DOUBT, CONTACT YOUR DEALER. 4 68 Dear Sir, Madam, Congratulations on the purchase of your air conditioner. In addition to air cooling, this air conditioner has three other functions: air dehumidification, air circulation and air filtration. You have acquired a high quality product that will provide you with many years of pleasure, on condition that you use it responsibly. [. . . ] OFF Programming the timer for OFF - when the unit is running. 88::88 88:88 1 Press the are flashing. 2 Press 3 Press the 4 Press or or push button; the 2 left digits of the 4 digits on the LCD display to adjust the hour. to adjust the minutes of the clock in intervals of 5 minutes. The timer is set. The circular time scale will be on between the present time to the OFF programmed time. The flashing bar on the time scale indicates the real time and moving a phase every 30 minutes ahead until it reaches the OFF timer time, then the black segments in the circular time scale will disappear. 4 74 Repeat OFF & ON Programming the timer for repeat OFF & ON - when the unit is running. 88::88 88:88 1 Press the are flashing. 2 Press 3 Press the 4 Press or or push button; the 2 left digits of the 4 digits on the LCD display to adjust the hour. to adjust the minutes of the clock in intervals of 5 minutes. The timer is set. 5 Repeat the above procedure while the digits are still flashing for setting the ON. The circular time scale will be on between the 00:00 time to the timer time off, off on and from the time on till 24:00. The flashing bar on the time scale indicates the real time and moving a phase every 30 minutes ahead. Repeat ON & OFF Programming the timer for repeat ON & OFF - when the unit is not running. 88::88 88:88 1 Press the are flashing. 2 Press 3 Press the 4 Press or or push button; the 2 left digits of the 4 digits on the LCD display to adjust the hour. to adjust the minutes of the clock in intervals of 5 minutes. The timer is set. 5 Repeat the above procedure while the digits are still flashing for setting the OFF. The circular time scale will be OFF between the 00:00 time to the timer time ON, and from the time OFF until 24:00. The flashing bar on the time scale indicates the real time and moving a phase every 30 minutes ahead. after plug out of the wall socket) you have to program the timer setting again. 4 75 7. CANCELLING THE TIMER FUNCTION In order to cancel the timer programming press the push button momentarily, then it will return to the time display. AIRFLOW Direct the airflow by adjusting the grill on top of the air conditioner. Move the grill, by pushing or pulling, in the middle (see illustration). Adjusting the airflow is as well possible by moving the direction of the vertical louvers. 1 3 Remove the active carbon filter and the 3MTM FiltreteTM filter from its plastic bag. [. . . ] Protect the unit against dust and store in a dry place, not accessible to children. 4 80 NOTE! Do not store the units disconnected, to prevent leakage of refrigerant. J TROUBLE SHOOTING Problem Cause No power supply. The outdoor unit is placed to high. Solution Connect to a functioning outlet and switch on. Wait 3 minutes until the temperature has decreased, and turn on the unit again. The maximum distance from the top of the outdoor unit to the floor is 150 cm (Refer to chapter B). [. . . ]