User manual ZIBRO SRE 149 TC

[. . . ] If a particular room is smaller than the specified space, always put a window or door slightly ajar ( 2. 5 cm). We also recommend doing this in highly insulated or draught-free rooms and/or at altitudes above 1, 500 metres. Do not use your heater in cellars or other underground areas. THE RIGHT FUEL Only use Class C1 paraffin fuel in accordance with BS2869; Part 2, or equivalent. Your heater has been designed for use with high-quality water-free pure paraffin oil, such as Zibro Extra or Zibro Kristal. [. . . ] Prior to igniting the heater, always check for sufficient fuel in the removable tank. E SETTING THE REQUIRED TEMPERATURE The temperature setting can only be adjusted, when the heater is burning. First press either of the two keys to min. ) to set the temperature to a switch on the function (the C mark and 4-digit will start blinking). Next, adjust the temperature using the key on the right ( 4 46 higher setting and the key on the left ( hour) to lower the temperature. After approximately 10 seconds the C mark and 4-digit will stop blinking and the setting will be locked (Fig. The available temperature settings range from 6C minimum to 28C maximum. When the heater has been unplugged (or after a power failure), the temperature will reset to the factory setting of 20C. F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key immediately after that. The TIMER lamp and the 4-digit will start blinking. hour) to set the hours and the key on the right 2 Use the adjustment keys Use the key on the left ( ( min. ) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the 4-digit will show CLOCK again and the TIMER lamp G: The TIMER indicator light indicates that the timer function has been switched on. will light up, indicating that the timer function has been activated (Fig. G). 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. G When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. SWITCHING OFF THE HEATER There are two ways to switch off the heater. 1 Press the button . Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). 4 47 H THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE INFORMATION Temperature within the heater too high. The heater has been in operation continuously for a period of 48 hours and has turned itself off automatically. Contact your dealer. In case of any malfunctioning the information display will tell you what is the matter. efefeeee- 0 0 1 1 2 5 6 7 e- 8 e- 9 -- : --- : -- + + Out of fuel. Too little ventilation. Always contact your dealer for any malfunctioning not listed above. AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 48 hours continuous operation. If desired, you can switch the heater on again by pressing button (see section D). AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode cl 05 running back to cl 01. The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. When the burner is clean again, the heater will automatically switch back to the highest setting again. I CHILDPROOF LOCK The childproof lock can be used to prevent children accidentally changing the heater settings. [. . . ] Never use the heater in places where harmful gasses or fumes may be present (e. g. Always make sure that there is sufficient ventilation. 20 cm 50 cm 50 cm 150 cm 3 4 5 6 7 8 9 10 Defective electrical devices and batteries must be kept separate from household waste. Ask you local council or dealer for expert advice on recycling. 4 51 DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL b. v. i STERREICH PVG Austria VertriebsgmbH Salaberg 49 3350 HAAG tel: +43 7434 44867 fax: +43 7434 44868 email: pvgaustria@zibro. com e BELGI PVG Belgium NV/SA Industrielaan 55 2900 SCHOTEN tel: +32 3 326 39 39 fax: +32 3 326 26 39 email: pvgbelgium@zibro. com q SCHWEIZ PVG Schweiz AG Salinenstrasse 63 4133 PRATTELN tel: +41 61 337 26 51 +41 61 337 26 78 fax: email: pvgint@zibro. com 2 DEUTSCHLAND PVG Deutschland GmbH Siemensstrasse 31 47533 KLEVE tel: 0800 - 9427646 fax: +31 (0)412 648 385 email: pvgdeutschland@zibro. com 6 DANMARK Appliance A/S Blovstroed Teglvaerksvej 3 DK-3450 ALLEROED tel: +45 70 205 701 fax: +45 70 208 701 email: appliance@appliance-group. com 5 ESPAA PVG Espaa S. A. San Jos de Valderas II Comunidad "La Alameda" C/ Aurora Boreal, 19 28918 LEGANS (Madrid) tel: +34 91 611 31 13 fax: +34 91 612 73 04 email: pvgspain@zibro. com 3 FRANCE PVG France SARL 4, Rue Jean Siblius B. P. [. . . ]