User manual ZONET ZEW2507

[. . . ] ZEW2507 connects you with 802. 11g networks at up to an incredible 54Mbps!And for added versatility, it can also interoperate with all the up to 11Mbps 802. 11b products found in homes, businesses, and public wireless hotspots around the country. Soft AP supported by ZEW2507 can help you establish wireless LAN networking with lowest cost. Besides, WPS (Wi-Fi Protected Setup) simplify the security setup and management of Wi-Fi networks. [. . . ] 802. 1X 8 802. 11g Wireless USB Adapter 3. 1. 2 Network Under Network tab, you will know information of all surrounding wireless networks from the last scan. Click Rescan to update and refresh. 3. 1. 3 Link Status Link status page shows detail information about the current connection. 9 802. 11g Wireless USB Adapter 3. 1. 4 Advanced The Advanced tab shows Advance function of UI Enable Tx Burst: Ralink's proprietary frame burst mode. Enable TCP Window Size: Check this box and the configuration utility will adjust TCP window size automatically to get better performance. Fast Roaming at: Fast to roaming, setup by transmitting power Enable CCX(Cisco Compatible eXtensions): a. Enable Radio Measurement: channel measures every 0~2000 milliseconds 3. 1. 5 Statistics Statistics tab displays the detail counter information based on 802. 11 MIB counters. This page translates that MIB counters into a format easier for user to understand. 10 802. 11g Wireless USB Adapter 3. 1. 6 WMM WMM Enable: Enable Wi-Fi Multi-Media WMM - Power Save Enable: Enable WMM Power Save Direct Link Setup Enable: Enable DLS (Direct Link Setup). This function will greatly improve the data transfer rate between WMM-enabled wireless devices. MAC Address: Input the MAC address of another WMM-enabled wireless device you wish to establish a direct link. Tear Down: If you want to remove a specific wireless device from DLS table, select the device and click this button to remove it. 3. 1. 7 WPS WPS tab supports the configuration setup using PIN configuration method or PBC configuration method. WPS(Wi-Fi Protected Setup) simplify the security setup and management of Wi-Fi networks. 11 802. 11g Wireless USB Adapter PIN: Enter the Pin code and click PIN to automatically connect ZEW2507 with wireless devices around. PBC: Click PBC to complete auto-check and connections between ZEW2507 and other wireless device. Disconnect: to disconnect the connected wireless network. 12 802. 11g Wireless USB Adapter 3. 2 AP Mode ZEW2507 also can serve as an access point to transmit wireless signals and create wireless network, allowing other wireless clients to access the network. Right-click the tray icon and select Switch to AP Mode. 3. 2. 1 Configuration In soft AP configuration Utility page, you can make some basic configurations, such as wireless network name, mode, channel and authentication. 13 802. 11g Wireless USB Adapter Click Security Setting button to make different security configurations of wireless communication, and you can choose the authentication type or encryption type. Note: 1. ASCII characters include any numbers/letters and characters. 14 802. 11g Wireless USB Adapter 3. 2. 2 Access Control Choose Access Control tab to start MAC control. After editing the MAC address access list, only the MAC in the Allow All list could access the Soft AP. 3. 2. 3 MAC Table MAC Table page shows the information of the wireless devices accessed to this soft AP. 15 802. 11g Wireless USB Adapter 3. 2. 4 Switch to Working Station mode In the Soft AP mode, right-click the icon in the system tray and choose Switch to Station Mode, then ZEW2507 is switching to working station mode with an interface of working station. 16 802. 11g Wireless USB Adapter 3. 3 Use Zero Configuration Windows XP and Vista has a built-in wireless network configuration utility "Windows Zero Configuration" (WZC). It is a built in service to configure your wireless clients from Windows 1. Start using WZC, right click the tray icon Configuration as Configuration utility. Double click the on the system tray to check the wireless network, wireless network icon choose the network and click Connect to setup the association. 3. If your wireless router has been encrypted, there will be a window appeared for input the key. Please input the key and click Connect, then the connection connect. 17 802. 11g Wireless USB Adapter 4. To configure the wireless connect properties, please right click the wireless icon in the system tray and choose Status to open the page Wireless Network Connection Status. 5. Click Properties button in General page and choose the tab Wireless Networks to add the SSID of available network by clicking Add, if there are several available networks, linking priority could be configured by the button Move up and Move down. -20 ~ 70 °C Humidity 10% ~ 90% (non-condensing) Dimension(L x W x H) 87 x 24. 8 x 11. 5 mm Weight 16. 1g 23 802. 11g Wireless USB Adapter Chapter 6. [. . . ] Nothing happens when I click Launch config utilities Please make sure ZEW2507 is inserted into your computer's USB port. If the Ralink configuration utility's icon is black, ZEW2507 is not detected by your computer. I can not establish connection with a certain wireless access point Click Connect for few more times. If the SSID of access point you wish to connect is hidden (nothing displayed in SSID field in Network tab), you have to input correct SSID of the access point you wish to connect. [. . . ]