Detailed instructions for use are in the User's Guide.
[. . . ] Operation Manual
CONTENTS
USAGE AND SAFETY PRECAUTIONS · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Introduction · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Controls and Functions · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4
Top Panel · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 Rear Panel · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4
Preparations
························································
6
Inserting Batteries and a SmartMedia card · · · · · · · · · · · · · · · · · · · · · · · · · · · 6 Getting Connected · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7
Quick Guide (Let's Play) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8 Listening to Patches (Play Mode Operation) · · · · · · · · · · · · · · · · · · · · 10
Panel Display in Play Mode · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Selecting a Patch · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Using the Tuner Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Using the Easy Edit Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Using the Sampler Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Using the Rhythm Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10 10 11 12 13 16
Changing the Sound of a Patch (Edit Mode)
····················
18
Patch Configuration · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18 Basic Edit Mode Steps · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18 Storing and Swapping Patches · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 20
Other Functions
···················································
21
21 23 23 25 26
Using the Hold Delay Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Changing the Patch Call Method · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Using the Pedal to Control an Effect · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Adjusting the Expression Pedal · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Storing Rhythm Patterns and Samples as Part of a Patch · · · · · · · · · · · ·
Assigning a rhythm pattern to a patch · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 26 Assigning a sample to a patch · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 27
Using a SmartMedia card (Utility Mode)
·····························
28
Basic utility mode operation steps · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 28 Utility mode functions · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 29
All Initialize/Factory Recall
·········································· ····································
32
Effect Types and Parameters
33
33 33 35 35 35 36 37 38
PICKUP SELECTOR Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · DRIVE Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · EQ (Equalizer) Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ZNR/D GATE (ZOOM Noise Reduction/D Gate) Module · · · · · · · · · · · · · · CABINET Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · MODULATION Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · DLY/REV (Delay/Reverb) Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · TOTAL Module · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Troubleshooting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 39 Specifications · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 39
Patch List
·························································
40
USAGE AND SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows:
· · · · Extreme temperature High humidity or moisture Excessive dust or sand Excessive vibration or shock
USAGE AND SAFETY PRECAUTIONS
· Handling
Caution
This symbol indicates explanations about extremely dangerous matters. If Warning users ignore this symbol and handle the device the wrong way, serious injury or death could result.
This symbol indicates explanations about dangerous matters. If users ignore this Caution symbol and handle the device the wrong way, bodily injury and damage to the equipment could result.
Please observe the following safety tips and precautions to ensure hazard-free use of the 708II.
Since the 708II is a precision electronic device, avoid applying excessive force to the switches and buttons. [. . . ] In this condition, parameter knobs 2 and 3 have the following functions.
GAIN The currently selected effect is adjusted by the pedal. Which parameter is controlled depends on the effect type.
Lit
Parameter knob 2 Sets the value for the fully raised position of the pedal. Parameter knob 3 Sets the value for the fully lowered position of the pedal.
REV The effect type currently selected for the DLY/REV module is adjusted by the pedal. Which parameter is controlled depends on the effect type.
6.
VOL The master volume is adjusted by the pedal.
SAMPLER The sampler function is switched on/off by the pedal. Pushing the pedal all the way down toggles between sampler on ([PEDAL] LED lit) and sampler off ([PEDAL] LED flashed). Also if a module is currently off, selecting it with the [PEDAL] key will cause its [PEDAL] LED to light and the module will temporarily come on. If a patch is stored in this condition, the module will be stored as ON. The actual parameter that is controlled by the pedal depends on the effect type. 33 38.
Use parameter knobs 2 and 3 to set the PDLMIN value (when pedal is fully raised) and PDLMAX value (when pedal is fully lowered). The setting range for both values is 0 10.
When you operate parameter knob 2, the indication "PDLMIN" appears on the display. When you operate parameter knob 3, the indication "PDLMAX" appears on the display. Setting PDLMIN or PDLMAX to 0 means that the parameter assigned to the pedal will be at the minimum value. Setting PDLMIN or PDLMAX to 10 means that the parameter assigned to the pedal will be at the maximum value. When the 708II is in the default condition, PDLMIN is set to 0 and PDLMAX is set to 10. As the pedal is depressed, the parameter value gradually increases from minimum to maximum.
Other Functions
HINT
The above procedure for assigning a module/effect type to the expression pedal can be carried out also in edit mode.
3. Use the MODULE [E]/[R] keys to select the TOTAL module.
MIN=0
MAX=10
24
ZOOM 708II BASS
For example, when PDLMIN is set to 4 and PDLMAX to 8, the parameter adjustment range will be limited as shown in the illustration below.
7.
Press the [STORE/EXECUTE] key to store the patch.
The module which is assigned to the pedal will automatically be stored as ON.
8.
MAX=8
In play mode, move the pedal while playing your bass.
The parameter assigned to the pedal changes.
MIN=4
9.
Push the pedal fully down.
When PDLMIN is set to 7 and PDLMAX to 2, pushing the pedal decreases the parameter value, and the range is as shown below.
The module which is assigned to the pedal is switched between on and off. If the pedal is assigned to the sampler, the sampler function is switched on or off.
NOTE
If the pedal is assigned to the volume, pushing the pedal fully down does not perform any switching action.
MIN=7
MAX=2
Adjusting the Expression Pedal
The expression pedal is adjusted for optimum operation at the factory, but sometimes, readjustment may be necessary. If pushing the pedal fully down does not have a strong effect, or if the volume or sound changes excessively even when the pedal is only lightly pushed, adjust the pedal as follows.
Other Functions
1.
Turn power to the 708II on while keeping the [PEDAL] key depressed.
The indication "MIN" appears on the display.
2.
With the expression pedal fully raised, press the [STORE/EXECUTE] key.
Push strongly, so that pedal touches here.
When foot is lifted, pedal returns slightly.
The display indication changes to "MAX".
4.
Press the [STORE/EXECUTE] key.
MAX
The adjustment is completed, and the unit returns to the play mode.
HINT
3.
Push the expression pedal fully down and then lift your foot off the pedal.
· The position of the pedal in step 3 determines the on/off switching point. If you want the pedal to perform on/off switching with a lighter touch, set the pedal to a somewhat higher position. · If the indication "ERROR" appears, return to step 2 and repeat the procedure.
The pedal goes back a little.
ZOOM 708II BASS
25
Storing Rhythm Patterns and Samples as Part of a Patch
The patches of the 708II can contain not only information about effect type and parameter settings but also about rhythm patterns and samples stored on a SmartMedia card. Using this capability, you can quickly switch rhythm patterns on the fly, or you can have the same sample play every time you call up a certain patch.
Assigning a rhythm pattern to a patch
By assigning rhythm patterns to patches, you can have the rhythm change in sync with the patches.
5.
Press the [STORE/EXECUTE] key to store the patch.
Assign other rhythm patterns to other patches in the same way.
6.
1.
In play mode, select the patch to which you want to assign a rhythm pattern, and press the [EDIT] key. Press the [EDIT] key once more.
When all patches have been prepared, press the [PATCH SYNC] key so that the LED of the key is lit.
When the [PATCH SYNC] key is set to ON, patches and rhythm patterns are switched in sync.
2. [. . . ] REVMIX 0 15 Parameter 3 Adjusts reverb sound mix.
TYPE 8 TYPE 4
MN-DLY (Mono delay)
This is a monaural delay with a duration of up to 1. 5 seconds.
HLDDLY (Hold Delay)
TYPE 5
PP-DLY (Ping-Pong Delay)
This is a hold delay effect that lets you record a phrase of up to 2 seconds during a performance and play it back repeatedly. When "Mn" (Manual) is selected and a foot switch is pressed, recording is carried out until the switch is pressed again or until 2 seconds have elapsed.
TIME 1 99, 1. 0 2. 0, Mn Parameter 1 Adjusts recording time from 10 ms to 990 ms in 10-ms steps (1 - 99), and from 1. 0 to 2. 0 seconds in 100-ms steps (1. 0 2. 0). When "Mn" (Manual) is selected, recording is carried out for as long as a foot switch is depressed (up to the maximum of 2 seconds). MODE Parameter 2 Selects playback mode for recorded phrase.
nL, So, rS
When two amplifiers are used, this serves as a ping-pong delay effect with a duration of up to 1. 5 seconds. [. . . ]