Detailed instructions for use are in the User's Guide.
[. . . ] OPERATION MANUAL
© ZOOM Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited.
Usage and safety precautions
SAFETY PRECAUTIONS
In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and handle the device the wrong way, serious injury or death could result. If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result. [. . . ] There are 2 types of effects adjustable by their mixer SEND LEVELS (signal volumes sent to the effect) and they can be used together.
Arrangement
Display
Monaural
Arrangement
Monaural
Display
Arrangement
Monaural ×2
Display
Monaural ×2 Stereo
Arrangement
Display
Stereo
Arrangement
Monaural ×8
Display Arrangement
Monaural ×8
Stereo
Display
Stereo
46
Effect
Input/output of the insert and send return effects
There are 2 types of effects processors built in to the R16--insert effects and send return effects. Insert effect/send return effect
INPUT 1-8
TRACK 1-16
INSERT EFFECT
You can use insert effects on specific channels.
SEND RETURN EFFECT
The built-in effects in the send return effect of the mixer.
Insert effect points CHORUS/DELAY Input
You can select inputs to apply effects to signals before recording them to recorder tracks.
The recorder (recording)
REVERB
Send level
(Signal volume sent to the effect)
The track mixer Track
Apply processing to the playback sound of any audio tracks in the track mixer.
Master
Process the final stereo mix just before the [MASTER] fader (signals recorded to the master track).
Mix (return) with the original sounds of the sent track.
Mix down The master track (recording)
Insert effect signal flow
Put the insert effect on a monaural input and output in monaural.
Send return effect signal flow
Ref. : Insert effect position
P. 52
47
Insert effect/send return effect
Uses of effects and patches
Insert effects and send return effects are selected and adjusted the same way. You can select the most appropriate modules from the algorithms, edit types and parameters and use saved patches. There are a few major differences between the two types of effects when making settings. For a SEND RETURN EFFECT, you adjust the send level of the signals using the mixer. Other functions are "IMPORT" to get patches from another project and "REC SIGNAL" to apply the effect only to monitoring. The use procedures of effects are the same when using the R16 as an audio interface and control surface, but the patches are initialized when the unit is not used as a recorder.
Select effect & patch Effect
<INSERT EFFECT> <SEND EFFECT>
1 2 3
Press until the red light turns on.
Red light on. Press [PLAY/ MUTE/REC].
or
Press [INSERT EFFECT] or [SEND RETURN EFFECT].
Press [ENTER] to turn on/off.
Select the algorithm.
Algorithm name Patch number: Patch name
INSERT EFFECT
Algorithm name Number of patches on display (programmed patches) Algorithm suitable for guitar/bass recording 30(22) CLEAN DISTORTION ACO/BASS SIM 30(20) BASS For microphone recording, such as vocals 50(30) MIC For 2 independent channels (2 mono inputs/outputs) 50(30) DUAL MIC For recording synthesizers, electric pianos and other lineoutput instruments 50(40) STEREO Algorithm with 8 independent channels of input/output 8×COMP EQ Processing for final stereo mixes MASTERING 20(10) 30(21) 50(40) 20(10)
Insert effect example
Insert effect insertion point Change algorithm
CLEAN <IN1> No. 00:Standard E
C L E A N , D I S T O R T I O N , E (edit mark): items ACO/BASS SIM, are already edited BASS, MIC, DUAL MIC, STEREO, 8x COMP EQ, MASTERING CHORUS/DELAY REVERB
Send return effect example
SEND CHORUS/DELAY No. 00:ShortDLY
4
Select the patch.
CLEAN <IN1> No. 15:Standard E Press [ ].
Change patch
SEND RETURN EFFECT
Algorithm name on display Process final stereo mix signals CHORUS/DELAY Process final stereo mix signals REVERB Number of patches (programmed patches) 30(18) 30(22)
EDIT IMPORT INPUT SOURCE REC SIGNAL
P. 53 P. 55 P. 51 P. 57
48
Effect
Insert effect insertion position
You can change the insert position of the Insert Effect. Insert effect>Patch sel>Input source
1
Press [INSERT EFFECT].
4
Select >INPUT
No. 00:Standard >INPUT SOURCE
SOURCE .
Change menu
Effect on/off switch.
If "INSERT EFFECT Off" is displayed,
press [ENTER].
Press [ENTER]. Input Source INPUT1
Change input place
2
Select the algorithm/patch.
Current insert position
Change algorithm
5
Set source of input into effect.
Input Source INPUT8 Input Source TRACK8 Press [ENTER].
On display Input Input1~Input8 Track1, Track2 Track1/2, Track3/4 Master Mixer input Single mixer input Output from either monaural track 1 or 2 Output from either stereo track or 2 monaural tracks Just before the [MASTER] fader All track 18 outputs All track 916 outputs Insert place Change input place
CLEAN <IN1> No. 00:Standard
Change patch IN** IN**/** TR** TR**/** IN*~** TR*~** MASTER Inserted in INPUT ** Inserted in INPUTS ** and ** Inserted in TRACK ** Inserted in TRACKS ** and ** Inserted in INPUTS * to ** Inserted in TRACKS * to ** Inserted in the master track
3
NOTE
Press[
].
With 8 x Comp EQ setting case Track1-8 Track9-16
· You can select a single INPUT (1~8) only when you have chosen the CLEAN, DISTORTION, ACO/BASS SIM, BASS or MIC algorithm. · You can select Track 1-8 or Track 9-16 only when the 8 x COMP EQ is chosen as the algorithm. · INPUT 1-8 can be selected only when the 8 x COMP EQ algorithm has been chosen. · After you select an insertion place, if you change the algorithm to 8 x COMP EQ, the insertion place will be changed to Input 1-8, Track 1-8 or Track 9-16 (depending on the previous setting). · To insert into a single monaural track output, you must select TRACK 1 ~ TRACK 8. To insert into a two monaural tracks or a stereo track, you must select TRACK 1/2 ~ TRACK 15/16. If you want to insert before the MASTER FADER, you must select MASTER.
6
HINT
Press[
].
Current insert position
CLEAN <TR8> No. 00:Standard
Change the insertion place of the insert effect. When a project is at the default status, the insert effect is inserted on INPUT 1. To change this place, select an INPUT SOURCE at Step 4:
49
Insert effect>Patch sel>Input source
Insert position of insert effect
Inserting the INSERT EFFECT into 2 monaural inputs (DUAL algorithm)
Inserting an INSERT EFFECT into a stereo input (Stereo Master algorithm)
Inserting an INSERT EFFECT on 8 inputs (8 x COMP EQ algorithm)
50
Effect
Insert effect Send return effect
: Patch editing
You can create patches that combine effects together, change effect types in patches, or change processing however you like by adjusting the depth of effects using their parameters.
Insert effect/send return effect>Patch sel>Edit
or
Press [INSERT EFFECT] or [SEND RETURN EFFECT].
Edit effect modules
1 2 3 4
Effect on/off switch.
If "INSERT EFFECT Off" is displayed, press [ENTER].
5 Turn the effect types on/off.
Effect module off
Compressor Off Press [ENTER] to switch.
Type (effect module) ON
Select the algorithm/patch.
CLEAN <IN1> No. 15:Standard E Press [ ].
Change algorithm
COMP/LIMITER Compressor
Effect type
E
E: Edit mark Shown after you edit or change
Change patch
Set the effect module
Select >EDIT .
No. 15:Standard >EDIT Press [ENTER]. E
Change item
6
Select the effect module.
COMP/LIMITER E Compressor MOD/DELAYE Chorus
Effect type Change module
HINT
· Some patches say "Empty, " because no modules in the patch have been set yet. · When you want to edit the ZNR module, go to the page with "TOTAL" in the first row. · You can individually edit the modules arranged in the L/R Channels of the DUAL MIC ALGORITHM. Your selection is the left channel when the first row displays "L" and the right channel when the first row displays "R. " · In the 8 x COMP EQ ALGORITHM, each channel has its own HPF, COMPRESSOR and EQ modules and you can turn each effect module on/ off on each channel independently. [. . . ] · If the EQ gain of the track mixer is set extremely high, the sound may be audibly distorted even if the fader is lowered. · When an insert effect is applied to an input, check whether the effect output level (patch level) setting is appropriate. Problems with effects · · · · · · · · · · · · · · · · · · · · Insert effect cannot be inserted. · When using the 8x COMP EQ algorithm, the selection of insert points is limited (P. 49). [. . . ]